Bolid Signal-10 Instruction Manual download pdf

DIP-34PA

Addressable Photoelectric Smoke Detector

INSTRUCTION MANUAL

GENERAL

DIP-34PA Threshold Addressable Photoelectric Smoke Detector (hereinafter referred to as the DIP-34PA or the detector)

is designed to be used in a fire alarm system in order to initiate fire alarms.

The DIP-34PA operates under control of the Signal-10 Intrusion and Fire Alarm Panel which the detector is connected to.

Up to ten detectors, each having its own address between 1 and 10, can be brought into a single Signal-10 alarm loop

which is configured with the Type 14, Fire Threshold Addressable Alarm Loop.

The DIP-34PA detects smoke inside its smoke chamber by sensing light reflected by smoke particles and responds with

its states to the Signal-10. Depending on detected smoke amount these states can be Norm, Fire Alarm, Trouble, Dusty,

and Test.

The version of DIP-34PA software is 1.02. Please read the Signal-10 User’s Manual to get more information about DIP-

34PA operation.

The detector’s operability must be periodically tested either by using test aerosol (as described below) or by means of a

remote laser tester (such as the tester produced by the System Sensor Company).

SPECIFICATIONS

Sensitivity 0.05 - 0.2 dB/m (1.2 %/m to 4.7 %/m)

Response Time 10 s max

Ingress Protection Rating IP 41

Input Voltage (via an alarm loop of a Signal-10) 9 ÷ 30 VDC

Current Consumption (via an alarm loop of a Signal-10) 0.4 mA max in quiescent mode

Pre-operation Time 60 s max

The number of detectors per alarm loop Up to 10

Operating Temperatures

−30 to +55°C

Storage Temperatures

−50 to +50°C

Humidity 93% at 40°C, non-condensing

Overall Dimensions (diameter x height)

100 mm × 46 mm max

Weight 0.2 kg max

Average Lifetime at least 10 years

STANDARD DELIVERY

Find the following unpacking the DIP-34PA:  DIP-34PA Detector

 Mounting Base

 This Instruction Manual

 Address Sticker

 Protective Cover

MOUNTING

The DIP-34PA can be mounted on a ceiling, suspended ceiling, wall, wire rope, column, or any other structural. The

detector is not designed to be mounted within the premises where air velocity values exceed 15 m/s.

Figure 1 shows three ways of attaching the detector.

To attach the detector to a solid surface (variant A) use the mounting base provided (see also the drilling pattern in Figure

2, at the left). For doing this match the detector mark with the short mark line on the mounting base, and then turn the

detector clockwise until the detector mark will be aligned with the mark 3 as shown in Figure 1 (A).

1 2 3 4

Summary of Contents

Page 1 - DIP-34PA

DIP-34PA Addressable Photoelectric Smoke Detector INSTRUCTION MANUAL GENERAL DIP-34PA Threshold Addressable Photoelectric Smoke Detector (hereinaft

Page 2 - PROGRAMMING

To build the detector into a suspended ceiling use separately purchased mounting kits MK-1 (variant B) or MK-2 (variant C). The size

Page 3

Assigning the DIP-34PA to an Address Bring the detector into a disarmed alarm loop of the Type 1 of a Signal-10 or to a 10V÷12V power supply. In 6 sec

Page 4

BOLID ONE YEAR LIMITED WARRANTY Bolid Company and its divisions and subsidiaries («Seller»), 4 Pionerskaya Str., Korolev 141070, Moscow Region, Russi

Bolid Signal-10 Instruction Manual

Browse online or download Instruction Manual for Security access control systems Bolid Signal-10. bolid Signal-10 Instruction manual User Manual

Summary of Contents

More documents for Security access control systems Bolid Signal-10

Comments to this Manuals

Bolid Signal-10 Instruction Manual

Browse online or download Instruction Manual for Security access control systems Bolid Signal-10. bolid Signal-10 Instruction manual User Manual

Summary of Contents

More documents for Security access control systems Bolid Signal-10

Comments to this Manuals

Related products and manuals for Security access control systems Bolid Signal-10